Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
This article in the next paragraphs in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is truly stimulating. You should check it out.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily available, the job can relocate speedily; if you have to open up a wall surface to get rid of the old tub and position the brand-new bath tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the job as well as fit trying it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration using one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will assist you mount a brand-new bathtub in your bathroom if you have already purchased a new tub and don't need to change the arrangement of your previous water supply pipes.
Your tools and product list need to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome because of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit all-time low of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water system and also check all joints and new pipework for leakages and also tighten them if necessary. Fill the tub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait till the bathtub has been used at least once as this will settle it into its final setting.
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split an inflexible seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in issues with dampness and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our excerpt on Tools You Need to Install a New Bathtub . Thanks a lot for spending some time to read our content. Are you aware of someone else who is occupied with the topic? Please feel free to share it. Thanks so much for taking the time to read it.
Book Maintenance
Report this page